arm center
英 [ɑːm ˈsentə(r)]
美 [ɑːrm ˈsentər]
网络 装备中心
双语例句
- In June, the company announced the establishment of new CPU Design Center in Hsinchu, Taiwan its first such center in Asia which will be dedicated to the series.
今年六月，ARM宣布在台湾新竹成立一座专门研发这款微处理器的CPU设计中心。这也是该公司在亚洲成立的首个CPU设计中心。 - To maintain the balance the dancer could do moving the arm, leg, or torso to change the Center of Gravity.
为保持平衡，舞者可以运用胳膊，腿，或者躯干来调整重心位置。 - She took the boy's arm and brought him to the table at the center of the room and there she made him sit.
她拉着男孩的胳膊，把他带到屋子中间的桌子旁边，让他坐下。 - The thickness of each arm decreased from a wide center to a narrower tip.
各条胳膊的厚度从宽大的中心向顶端逐渐变得更加狭窄。 - Effect of secondary dendritic arm spacing on center carbon segregation of slab
连铸板坯二次枝晶臂间距对中心碳偏析的影响 - Counters and ionization chambers are applied to sensors, and microprocessor based on ARM IP is applied to center controller in the instrument. It is achieved to monitor nuclear radiation and baneful gas in an instrument.
采用计数管与电离室作为传感器，以基于ARM内核的微处理器为中心控制器，在同一仪器上实现了对核辐射和化学有害气体的监测。 - The agreement between the calculated and measured is good. The results show that, the arm length mainly influences the center frequency, which increases from 3.8 mm to 4.7 mm, the center frequency decreases from 11.9 GHz to 8.9 GHz.
结果表明：臂长主要影响中心频率，臂长从3.8mm增大到4.7mm时，中心频率从11.9GHz下降到8.9GHz； - The control center is carried out based on the ARM CPU, and takes on the home gateway function.
论文以ARMCPU为核心设计了住宅控制中心，实现了对远程访问的响应以及对住宅内设备的控制。 - Lever arm effect error, resulted from non-conformity of mounted position of the inertial measuring unit and center of mass of a vehicle causes an additional interference acceleration existed in an accelerometer output. It is one of the main error sources Of the inertial navigation system.
杆臂效应误差是由于惯性测量组件安装位置与飞行器质心不重合而引起加速度计输出中的附加干扰加速度，它是惯导系统的主要误差源之一。 - In this thesis, a practical scheme of high performance PMU is designed, in which ARM technology is used to realize the Ethernet communications among control center, substations and plants.
最后在上述理论研究基础上，设计了基于ARM技术的高性能PMU方案，该方案采用以太网作为数据交换手段。 - Hyperbolic analytic method of calculating pivot location of compensation block on a crane Lw& Horizontal distance from back coupling point of lift arm to center of rising reel.
起重机补偿滑轮铰点位置的双曲解析计算法Ld单顶滑轮中心到吊臂头部滑轮中心水平距离；Nd单顶滑轮中心到吊臂中心线垂直距离； - In the automobile four turn position finder has plumbing arm components, its processing precision request is very high, uses the processing center to be possible to realize, but the cost is very high.
汽车四轮定位仪中有一个垂臂零件，它的加工精度要求很高，采用加工中心可以实现，但成本很高。 - The system controls the logic of the data acquisition board by programmable logic device ( PLD) with the center of the ARM microcontroller and FIFO memory and provides the simulate waveforms.
系统以ARM微处理器和FIFO存储器为核心，利用可编程逻辑器件实现对整个底层数据采集系统的逻辑控制，并给出了时序控制部分的仿真波形。 - The arm width and the slot width influence the center frequency as well as the bandwidth.
臂宽和缝宽在影响中心频率的同时也影响带宽； - A whole design plan for a kind of frequency hopping radio is put forward. Adopting innovative ARM+ FPGA pattern as the hardware platform system, the hardware design project on center control unit and frequency hopping unit is given.
提出一种跳频电台的总体设计构想，采用ARM+FPGA架构作为硬件平台系统，给出中央控制单元和跳频单元的硬件设计方案。 - Maintenance of Tool Change Mechanical Arm of Machining Center
加工中心换刀机械手的维修 - We present a new scheme embedded center controller based on ARM, DSP and LINUX, the hardware and software of the development of embedded center controller is illustrated.
提出了采用一种非PC结构的，基于ARM、DSP与Linux的嵌入式中央控制器，介绍嵌入式中央控制器的硬件设计、软件设计。 - It connection tower body, and other parts such as erector beam, balance arm, and it can revolve 360 degree about the center of the tower body to lift the load.
它下面连接塔身，上部支撑起重臂、平衡臂等部件，可使塔机上部相对于塔身作360度自由回转，以完成各种起重作业要求。 - The control system is made up of monitor level, coordinate control level and bottom-level. ARM is the center of monitor-level. DSP and CPLD is responsible for the other two levels.
系统由ARM为中心的组织监控级、DSP和CPLD控制的协调控制级和底层执行级组成。 - Lever arm error is corrected through calculating the length of lever arm, which is equivalent to move the SAHMS to the swinging center, then Kalman filter method can be applied for self-alignment using the information that the velocity of swinging center approximate to zero.
该方案通过反求杆臂长度的办法实现杆臂效应补偿，等效地将系统移至摇摆中心，利用摇摆中心速度接近为零的信息，采用卡尔曼滤波实现系统自对准。 - The excavator arm trough plate functions as connecting the arm and bucket, increasing working range and Coordinate the center of gravity. So it is an important part of the excavator.
挖掘机斗杆用于连接动臂与铲斗，加大工作范围，协调整机重心，是挖掘机的重要组成部分。 - Put forward the method of teaching four-point arm position and orientation, and actualize the calibration of tool center frame.
提出了示教四点手臂位姿的方法，实现了工具坐标系的标定。